|Version 9 (modified by 5 years ago) ( diff ),|
wiserd was developed as a basic software building block of a distributed frequency-domain based spectrum sensing system consisting of a number of deployed spectrum sensors (SDR nodes) that are managed by the centralized controller. The main goal was to provision the SDR node with a monolithic (i.e. simple to deploy) relatively portable (i.e. with minimal number of software dependencies) application with fft based processing of time-domain RF signals that has ability to control RF and spectrum sensing parameters. Over time, the wiserd grew up to include other (not necessarily frequency domain and not receiver only) modules. The daemon type C++ application is divided into modules and is multithreaded. The block-diagram of the application is shown in Figure 1. It consist of the following functional modules:
- The main module (controller) handles user commands which can either be entered locally on a controlling terminal or sent from a remote controller over TCP.
- The radio module (uhd) handles all the communication to and from the radio device. While the current version of the module was designed to work with VITA standard, it was only thoroughly tested with USRP devices. If another radio device was to be used, this is would be the only module that needs to be tested/changed.
- The receiver module (rx) uses the radio device to receive IQ time samples at preset frequencies with preset sampling rates and forwards them to the receiver consumer modules. In addition to interfacing with consumers, the rx module is also used to assign consumer threads to processing cores based on real-time requirements. It can also be used for buffering and re-packetization.
- The transmitter module (tx) uses the radio device to transmit signals, received from transmitter producer modules as IQ time samples, at preset frequencies with preset sampling rates.
The producer/consumer modules are written following the factory method pattern:
- Receiver consumer modules receive the IQ time samples from the receiver module and process them. The same set of IQ samples is passed on to all consumers for arbitrary processing. At present, available receiver consumers are: fft_movavg_udp, fft_pow_udp, store_to_file.
- Transmitter producer modules send the IQ time samples to the transmitter module to be transmitted on the radio device. Present transmitter producers are: signal_from_file, waveform.
The wiserd code was written using Google style.
- fft_movavg_udp: performs the FFT on the time samples received from the receiver module, calculates the moving average and sends the results via UDP. The consumer name used to add the consumer while using the program is "fftmovingavgudp". Needed parameters: FFT length, averaging window length, UDP address and port.
- fft_pow_udp: performs the FFT on the time samples, calculates the power of each FFT bin and sends the results as arrays of 8bit numbers via UDP, with a preset minimal power corresponding to 0 and preset maximal power corresponding to 255. Consumer name is "fftpowudp". Needed parameters: FFT length, minimal power, maximal power, UDP address and port.
- time_samples_to_file: simply stores the time samples as complex 32bit floats in a binary file, with the real part coming first and imaginary second for each sample. Consumer name is "timesamplestofile". Needed parameters: the receiver output file name. The module will append information such as the receiver central frequency, sampling rate and file extension to the name of the file.
- fft_movavg_oml: performs the FFT on the time samples received from the receiver module, calculates the moving average and sends the results to the OML server. The consumer name is "fftmovingavgoml". Needed parameters: FFT length, averaging window length, OML server address and port (use server name "file" to store locally), OML filename.
- fft_sigpower_oml: performs the FFT on the time samples receivd from the receiver module, calculates the peak power in dBm and 3dB bandwidth each second, and on used command sends the results to the OML server. Needed parameters: FFT length, OML server address and port (use server name "file" to store locally), OML filename.
- signal_from_file: reads IQ time samples stored as complex floats from a file and sends them to the transmitting module. Producer name is "signalfromfile". Needed parameters: file name.
- waveform: has a number of predefined waveforms to be sent to the transmitting module. Consumer name is "waveform". Needed parameters: waveform type, waveform frequency (depending on the type).
The parameters may be entered in the command line or sent via TCP. The default port is 5123. To set a parameter, the user must enter its name preceded by --, and followed by the desired value. For example, to set receiver frequency to 700 MHz the user can enter the following:
To get the current value of any parameter, the user must enter only the parameter name preceded by --:
Adding the described modules is done using the parameter --addmodule, followed by the module name. In order to run a module for a specified time, the parameters --recv_running_time or --tran_running_time need to be set to the desired time (in milliseconds), and the flag --timed needs to be used.
--addmodule Add a module (RX modules: 'timesamplestofile', 'fftmovingavgoml', 'fftmovingavgudp', 'fftsigpoweroml', 'fftpowudp'; TX modules: 'signalfromfile', 'waveform') --delmodule Delete a module --timed Module runs for a predefined time and then gets automatically deleted --uhd_rx_antenna Receiver antenna ('RX2', 'TX/RX') --uhd_tx_antenna Transmitter antenna ('TX/RX') --uhd_rx_freq Receiver central frequency --uhd_tx_freq Transmitter central frequency --uhd_rx_rate Receiver sampling rate --uhd_tx_rate Transmitter sampling rate --uhd_rx_gain Receiver gain in dB --uhd_tx_gain Transmitter gain in dB --uhd_rx_bandwidth Receiver bandwidth --uhd_tx_bandwidth Transmitter bandwidth --recv_numbins Number of FFT bins. --recv_avgwinlen Averaging window length. --recv_oml_filename Output filename for OML --recv_oml_servername OML server name ('idb2:3003' or 'file') --recv_oml_output_type Output data type for OML ('blob', 'vector', 'scalars') --recv_udp_port UDP port --recv_udp_uri UDP uri --recv_min_power Minimal considered power in dBm --recv_max_power Maximal considered power in dBm --recv_output_filename Filename for local storing the time samples (do not add the extension) --recv_running_time Running time for timed modules, in milliseconds --tran_wavetype Type of transmitted waveform, SINE, CONST, SQUARE, RAMP --tran_wavefreq Frequency of transmitted waveform --tran_amplitude Amplitude of transmitted waveform (max 0.7) --tran_wavefilename Name of the file containing the waveform --tran_running_time Running time for timed modules, in milliseconds
The latest version of the wiserd code is available in the git repository. To check out the latest code:
git clone firstname.lastname@example.org:/common/git/wiserd
To install required prerequisites:
apt-get install liblog4cxx10-dev libocomm-dev liboml2 liboml2-dev
The wiserd daemon is built and installed in /usr/sbin with:
make make install