wiki:crkit/Software/Firmware/Framework/R3_arch
close Warning: Can't synchronize with repository "(default)" (/common/SVN/crkit does not appear to be a Subversion repository.). Look in the Trac log for more information.

Version 12 (modified by khanhle, 12 years ago) ( diff )

--

R3 Architecture

Overview

With R3, we have included a dedicated control plane with RMAP processor which will handle all register map related accesses. In future releases, we may replace the RMAP processor with a real 32-bit soft processor such as Xilinx Microblaze, or equivalent processors.

The register maps associated with the control plane handle all Board related controls e.g. RF SPI, general purpose IOs, LEDs and so forth. Whereas, data plane centric register maps are maintained within the Tx and Rx Application modules. Within the APP module, we have an option of having a top level RMAP, and/or an application specific RMAP. Usually, the top level RMAP is shared among multiple applications, whereas application specific RMAPs are only designed for a particular application.

Figure 1 - R3 architecture overview



R3 architecture consists of following modules :

  • Ethernet Port - Ethernet framing function,
    • Rx - receives ethernet frames from Host. Performs CRC checking, and forwards error free payload to packet processor.
    • Tx - transmits ethernet frames to Host. Generates Ethernet header and CRC, IP payload is provided by packet processor.
  • Packet Processor - IP layer processing
    • Packet classification - RMAP, Data, and other (such as ARP and DHCP packets)
    • UDP is used for board level communication e.g. RMAP and Data packets
  • APP - User specific application

  • RF Port - DAC/ADC interfacing
  • Control Plane - RMAP and RF control
  • Timing Control - system wide clock control using clock enables

From Host, we can control the hardware (RMAP read/write operations) by sending RMAP ethernet frame messages. The packet classifier classifies and forwards packets according to its type :

  • RMAP packets -> RMAP Processor
  • Data packets -> Tx Buffer for APP processing
  • Other packets -> TCP/IP stack

For RMAP read operations, read data must be forwarded back to Host. This is accomplished by following operations :

  1. RMAP Processor forwards read data to Rx Memory Controller. Note : shared access to Rx buffer with dataflow.
  2. Generate IP and Ethernet frame for transmission back to host. Some control header information are added in the payload section for Host RMAP read synchronization.

Global Memory Map

R3 global memory map is currently divided into 4 regions : Common control, Common Interrupt Control, Receiver and Transmitter. 65Kbytes are reserved for each region. The total number of address bits are 32-bit, but we will only use the lower 16-bits per region e.g. 65Kbytes per region. Therefore, bits19-16 are used for region address decoding between Common control, Receiver and Transmitter as illustrated in figure 3.

Figure 2 - R3 Global Memory

No image "r3_glob_mem.jpg" attached to crkit/Software/Firmware/Framework/R3_arch

Common Control - Control Plane register map e.g. SPI, LEDs, and board level IO.
Common INTC - Interrupt Controller map. Individual interrupt lines from Common Control, XMTR and RCVR are consolidated in a single location. Once an interrupt is set (by INTR ethernet frame), Host shall read the INTC status register to identify which of the 3 regions has triggered an interrupt e.g. coarse parsing, followed by fine parsing.
XMTR - Transmitter register map.
RCVR - Receiver register map.

Figure 3 - R3 Top Address Decoding



Ethernet Frame Formatting

In this section, the ethernet frame payload structures are detailed for Host -> HW, and HW -> Host directions. Some header information are appended to provide additional control information.
Host -> HW : two types of Ethernet frames e.g. rmap and data frames.
HW -> Host : two types of Ethernet frames e.g. rmap read and data. The data frames are further classified in additional subtypes such as generic data, FFT data structures and so forth. Host may perform additional processing on the data structures.

Segmentation - this function is performed by the 'Tx Ethernet Interface' module. This module will automatically segment the data structure if size is greater than 1500 bytes (payload is stored in Rx Buffer). Some control information are appended to denote first, intermediate and last segment. Refer to HW -> Host for further details.

Control Flow

As with previous revisions, R3 control flow is message-based. Host sends commands to HW, where they get parsed and acted on accordingly. R3 control flow scheme is detailed in the Control Flow Diagram.

Multi-clocks Synchronization



Block Level Specifications

XMTR
RCVR
Control Plane


FPGA Architecture

The modularity of the FPGA architecture design provides a path for upgradeability. All main components can be upgraded or replaced as long as the integrity of IO interfaces are maintained.

Register Maps



Return ..

Attachments (3)

Download all attachments as: .zip

Note: See TracWiki for help on using the wiki.